Truck bodies built in British Columbia

Refrigerated bodies · Fleet guide

How to Spec a Refrigerated Body for Multi-Temp Delivery

In this guideStart with the freight, not the truckZones, dividers, and doorsThe insulation does the heavy liftingThe refrigeration unit is part of the quoteSize, weight, and the truck underneathRunning it day to daySpec it for the route you actually run

A lot of BC delivery routes are not one temperature. The same truck can leave the yard with frozen food, chilled dairy, and dry goods that just need to stay out of the rain. Run that load in a single-temperature box and you either freeze the dry goods or thaw the frozen ones. A multi-temp refrigerated body splits the box into zones, each held at its own temperature, so one truck does the work of two or three.

Start with the freight, not the truck

List what the truck carries on a normal week: frozen, chilled, and ambient are the usual three bands, and note how much of each goes out and in what order it comes off. The frozen load is usually the smallest share but the most temperature-sensitive, so it often gets its own zone at the front of the body, furthest from the rear door.

Zone sizes follow the freight split, not a standard split. A route that is mostly chilled with a small frozen top-up needs a different layout than one split evenly between frozen and chilled. Get the split wrong and one zone is always crammed while another runs half empty.

Zones, dividers, and doors

Zones are separated by insulated dividers or bulkheads. A movable divider earns its keep on mixed routes: the frozen zone can grow on a big frozen day and shrink when the chilled load is heavier. Fixed bulkheads are simpler and suit routes where the split barely changes.

Door placement matters as much as the divider. Every time the rear door opens, warm air comes in, and the zone nearest the door takes the most of it. Plan the loading order around it: freight coming off last goes in first, deepest in the body. Some operators add a side door for the chilled zone so the frozen zone stays shut on chilled stops — worth discussing at spec time, since adding a door later is a bigger job than building it in.

The insulation does the heavy lifting

A refrigerated body lives or dies on its insulation. Evermount builds refrigerated bodies with 100 mm PU foam walls and a 120 mm floor and roof, with an XPS insulated floor finished in aluminum chequered plate. That thickness holds a frozen zone at temperature while the chilled zone next door sits twenty degrees warmer.

The floor drain is standard on our reefer bodies, because washdowns and meltwater need somewhere to go. The insulated roll-up door and the powder-coated stainless-steel rear door frame keep the seal tight at the back, where most cold air escapes.

The refrigeration unit is part of the quote

A body without a unit is a well-insulated box. Evermount supplies the refrigeration unit as well — included in the quote or priced separately, whichever suits the buyer. Multi-zone work means a unit set up to hold more than one temperature, so unit and zone layout are specced together.

One thing to be clear about: Evermount supplies the unit, it does not service refrigeration units. Plan the unit's servicing with a refrigeration service provider, the same way you would for any reefer.

Size, weight, and the truck underneath

Refrigerated bodies run 10 to 20 ft, and body weight runs roughly 940 to 2,050 kg across that range. The unit, the dividers, and the load all add to what the chassis carries, so body size and truck payload need to be checked together before anything is ordered. A body that is right for the freight but too heavy for the chassis helps nobody. As a rough guide, a 10 ft body suits a tight urban route with a few multi-temp stops, while a 20 ft body suits a full day of mixed deliveries across the Lower Mainland.

Running it day to day

Pre-cool the body before loading, and load the frozen zone first so it spends the least time with the door open. Keep the dividers sealed — a divider left ajar turns two zones into one lukewarm one. Check the door seals and the floor drain on the regular walkaround; a worn seal costs more in lost cold than most operators realise.

When a panel, door, or seal needs attention, our Abbotsford repair and service shop handles refrigerated bodies, including bodies built by other manufacturers.

Spec it for the route you actually run

If you are running mixed-temperature loads out of one truck — or paying for a second truck to cover the temperature your first one cannot — a multi-temp body is worth a conversation. Bring the route: what you carry, how much of each temperature, and how many stops. The body gets built around that, in 10 to 20 ft, with the zones, doors, and unit to match.

Evermount Truck Solutions Ltd. — truck body manufacturer in Abbotsford, BC
Sales: +1 (250) 885-9335 · sales@evermount.ca · evermount.ca
Serving the Fraser Valley, the Lower Mainland, and fleets across BC. Proudly Canadian.

Refrigerated bodies run 10 to 20 ft. Final specifications are confirmed for each chassis and application.